The Roofing Book

Permitting Authorities / Town of East Greenwich - Building Department

Do you need a permit to replace a roof in East Greenwich, RI?

Adopted code

Town of East Greenwich - Building Department

The Town of East Greenwich Building Department, part of the Department of Public Works at 111 Peirce Street in Kent County, issues building permits in East Greenwich; its page directs applicants to the town's e-permitting portal. The Rhode Island State Building Code applies in East Greenwich as it does in every Rhode Island city and town. This listing covers the office's contact details and the rules state law sets for every Rhode Island town; it does not cover East Greenwich's own permit rules.

Roof code checklist: East Greenwich, RI

ItemAnswerCode citeSourceVerified
Permit to replace a roofNot published
Repair permit thresholdNot published
Layer limit / roof-overPublishedR908.3.1.1rules.sos.ri.gov2026-10-09
Deck & sheathingPublishedR905.2.1rules.sos.ri.gov2026-10-09
Drip edgeYesR905.2.8.5rules.sos.ri.gov2026-10-09
Ice & water shieldYesR905.1.2rules.sos.ri.gov2026-10-09
Mid-roof inspectionNot published
Impact-resistant (Class 4) roofingNorules.sos.ri.gov2026-10-09
Wind design criteriaPublishedrules.sos.ri.gov2026-10-09
Adopted codePublishedrules.sos.ri.gov2026-10-09
Contractor license / registrationYeswebserver.rilegislature.gov2026-10-09
Sales & use taxPublishedSec. 54.6webserver.rilegislature.gov2026-10-09

Each row comes from the sourced record on this page; full wording is in the table below. "Not published" means no official source for that item was found when the record was last verified.

Jurisdiction
Town of East Greenwich, Rhode Island
Jurisdiction type
city
Address
111 Peirce Street, Lower Level, East Greenwich, RI 02818
Contact
  • url: https://www.eastgreenwichri.gov/165/Building-Permits-Information
  • phone: 401-886-8618
Permit portal
Permit portal
Contractor registration required
Required
Adopted code
The Rhode Island One and Two Family Dwelling Code (RISBC-2, 510-RICR-00-00-2), which "adopts and incorporates as the Rhode Island One & Two-Family Dwelling Code the provisions of the International Residential Code (IRC), 2021 edition," effective December 1, 2025, and which applies "to the construction, alteration, enlargement, replacement, repair, equipment, use and occupancy and location of detached one-and two-family dwellings and multiple single-family dwellings (townhouses) not more than three stories in height" (R101.2). The State's adoption says "Chapter 8 is adopted with no changes" and "Chapter 9 is adopted with no changes," so the roof framing, sheathing and roof assembly rules apply as the International Code Council publishes them. The same code applies in every city and town: the State Building Code applies "to all buildings and structures" (R.I. Gen. Laws 23-27.3-101.0), and "the local cities and towns shall be prohibited from enacting any local building codes and ordinances in the future" (23-27.3-100.1.7). A 2026 act requires a newer edition: "The 2024 IRC, including any amendments thereto adopted by the building code standards committee ("BCSC"), shall take effect" for one- to three-family dwellings "not later than January 1, 2027" (P.L. 2026, ch. 377, adding subsection (f) to 23-27.3-100.1.5). Everything above is Rhode Island state law, the same in every city and town. In East Greenwich the Building Department, within the Department of Public Works, guides applicants through permitting and inspection, and takes permit applications through the town's e-permitting portal, according to the town's own page.
Drip edge
Required — Required on shingle roofs. Rhode Island adopts the 2021 International Residential Code with "Chapter 9 is adopted with no changes" (510-RICR-00-00-2), so Section R905.2.8.5 applies as published: "A drip edge shall be provided at eaves and rake edges of shingle roofs." Segments overlap by at least 2 inches, the drip edge extends at least 1/4 inch below the roof sheathing and at least 2 inches back onto the deck, it is fastened at no more than 12 inches on center, and "Underlayment shall be installed over the drip edge along eaves and under the drip edge along rake edges." A reroof is held to the same chapter: "Materials and methods of application used for recovering or replacing an existing roof covering shall comply with the requirements of Chapter 9" (R908.1). Everything above is Rhode Island state law, the same in every city and town. In East Greenwich the Building Department, within the Department of Public Works, guides applicants through permitting and inspection, and takes permit applications through the town's e-permitting portal, according to the town's own page. About drip edge
Ice & water shield
Required — Required statewide. Rhode Island replaces the International Residential Code's Table R301.2(1) with its own table for the whole state, and that table reads "Ice Shield Underlayment Required" "Yes" (510-RICR-00-00-2, R301.2). Section R905.1.2, adopted unchanged, then requires an ice barrier "for asphalt shingles, metal roof shingles, mineral-surfaced roll roofing, slate and slate-type shingles, wood shingles and wood shakes," consisting of "not fewer than two layers of underlayment cemented together, or a self-adhering polymer-modified bitumen sheet," extending "from the lowest edges of all roof surfaces to a point not less than 24 inches (610 mm) inside the exterior wall line of the building," and on roofs of 8:12 slope or steeper also "not less than 36 inches (914 mm) measured along the roof slope from the eave edge of the building." The rule does not apply to "Detached accessory structures not containing conditioned floor area." On a tear-off, an ice barrier membrane adhered to the deck may stay and be covered with an additional layer (R908.3, Exception). Everything above is Rhode Island state law, the same in every city and town. In East Greenwich the Building Department, within the Department of Public Works, guides applicants through permitting and inspection, and takes permit applications through the town's e-permitting portal, according to the town's own page. About ice & water barrier
Impact-resistant roofing
Not required — No impact-resistance requirement under state law. Rhode Island's residential code, the 2021 International Residential Code as the State adopts it (510-RICR-00-00-2), contains no hail or impact rule for roof coverings: neither UL 2218 nor a Class 4 rating appears in its chapters, its referenced-standards chapter or its adopted appendices, and the State's amendments do not mention either. Cities and towns may not enact building codes of their own (R.I. Gen. Laws 23-27.3-100.1.7), so none can add one. An owner may still choose an impact-rated roof covering. Everything above is Rhode Island state law, the same in every city and town. In East Greenwich the Building Department, within the Department of Public Works, guides applicants through permitting and inspection, and takes permit applications through the town's e-permitting portal, according to the town's own page.
Wind design criteria
Set by the State for each city and town. Rhode Island deletes the International Residential Code's wind maps and substitutes its own "Rhode Island Snow Load, Wind Speed and Frost Depth Table" (510-RICR-00-00-2, section 2.4), which lists a basic wind speed for every municipality by risk category; a house is ordinarily Risk Category II. For East Greenwich, the table lists a ground snow load of 30 psf and basic wind speeds of 118 mph (Risk Category I), 128 mph (Risk Category II), 136 mph (#) (Risk Category III) and 140 mph (*) (Risk Category IV). Under Table R905.2.4.1 an ultimate design wind speed of 128 mph calls for ASTM D7158 Class G or H (or ASTM D3161 Class A, D or F). The table's notes define two flags: "# - Wind-borne Debris Region greater than 130 MPH within a mile of "mean high coastal water line"" and "* - Wind-borne Debris Region In areas where wind speed is 140 mph (63.6 m/s) or greater." For asphalt shingles, Section R905.2.4.1 (adopted unchanged) requires shingles "tested in accordance with ASTM D7158" that "meet the classification requirements of Table R905.2.4.1 for the appropriate ultimate design wind speed," with packaging labelled to show it. Everything above is Rhode Island state law. In East Greenwich the Building Department, within the Department of Public Works, guides applicants through permitting and inspection, and takes permit applications through the town's e-permitting portal, according to the town's own page.
Roof layer limit / recover
Two layers at most. Rhode Island adopts the 2021 International Residential Code with "Chapter 9 is adopted with no changes" (510-RICR-00-00-2), so its reroofing section, R908, applies as published. Section R908.3.1.1 says "A roof recover shall not be permitted where any of the following conditions occur," and the third condition is "Where the existing roof has two or more applications of any type of roof covering." So one existing layer may be covered once, and a roof that already has two layers is torn off to the deck. The same section also bars a recover "Where the existing roof or roof covering is water soaked or has deteriorated to the point that the existing roof or roof covering is not adequate as a base for additional roofing" and "Where the existing roof covering is slate, clay, cement or asbestos-cement tile." A tear-off means "the removal of existing layers of roof coverings down to the roof deck" (R908.3). Cities and towns may not enact building codes of their own (R.I. Gen. Laws 23-27.3-100.1.7). Everything above is Rhode Island state law, the same in every city and town. In East Greenwich the Building Department, within the Department of Public Works, guides applicants through permitting and inspection, and takes permit applications through the town's e-permitting portal, according to the town's own page.
Deck & sheathing requirements
State rules from the base code. Rhode Island adopts the 2021 International Residential Code with "Chapter 8 is adopted with no changes" and "Chapter 9 is adopted with no changes" (510-RICR-00-00-2), so Section R803, Roof Sheathing, applies as published. Lumber roof sheathing follows Table R803.1: over rafters or beams 24 inches apart it must be at least 5/8 inch net thick. Wood structural panels "shall be identified for grade, bond classification and performance category by a grade mark or certificate of inspection issued by an approved agency," and their spans "shall not exceed the values set forth in Table R503.2.1.1(1) or APA E30." For shingles, "Asphalt shingles shall be fastened to solidly sheathed decks" (R905.2.1), and on any reroof "The structural roof components shall be capable of supporting the roof covering system and the material and equipment loads that will be encountered during installation of the roof covering system" (R908.2). Cities and towns may not enact building codes of their own (R.I. Gen. Laws 23-27.3-100.1.7). Everything above is Rhode Island state law, the same in every city and town. In East Greenwich the Building Department, within the Department of Public Works, guides applicants through permitting and inspection, and takes permit applications through the town's e-permitting portal, according to the town's own page.
Sales & use tax
7% Rhode Island sales and use tax, the same in every city and town; the only local add-on in the sales tax chapter is a 1% tax on meals and beverages. On a reroof the roofer pays the tax on the materials. The statute sets the rate: "for the period commencing July 1, 1990, the tax rate is seven percent (7%)" (R.I. Gen. Laws 44-18-18), and the Division of Taxation says "The sales tax is imposed upon the retailer at the rate of 7% of the gross receipts from taxable sales." The local tax in the chapter is imposed on "each and every meal and/or beverage sold within the state of Rhode Island in or from an eating and/or drinking establishment" (44-18-18.1). For construction work the Division's rule, which names roofing contractors, says "A contractor shall pay the tax as a consumer on the purchase of all materials, supplies, tools and equipment ... used by him in fulfilling either a lump-sum contract, a cost-plus contract, a time and material contract with an upset or guaranteed price which may not be exceeded, or any other kind of construction contract," unless the contractor sells the materials at an agreed price separate from the service or is in the business of selling such materials at retail; in those cases the contractor collects the tax from the customer (280-RICR-20-70-54, section 54.6(A)). Everything above is Rhode Island state law, the same in every city and town. In East Greenwich the Building Department, within the Department of Public Works, guides applicants through permitting and inspection, and takes permit applications through the town's e-permitting portal, according to the town's own page.

Local roofing hub

Roofing in East Greenwich, Rhode IslandCity hub

More roof permit pages in Rhode Island

East Providence, RIRoof permit Johnston, RIRoof permit Lincoln, RIRoof permit Middletown, RIRoof permit Newport, RIRoof permit Roofing in Rhode IslandState hub

Related guides

Denver-Metro Roofing Permits Filing a Hail Insurance Claim Colorado Hail Season Prep Hiring a Contractor

Working an insurance claim in East Greenwich, RI? Everything on this page (drip edge, ice & water shield, inspections, Class 4 rules) formatted as a claim-ready evidence pack: verbatim ordinance quotes, code section cites, verification dates, and official source links, ready to attach to a supplement. See a real sample pack (PDF, 4 pages, free).

Code items like drip edge and ice & water shield are what adjusters ask you to document.

Buy this jurisdiction's pack: $12 Delivered by email within minutes. Digital download: all sales are final once delivered, except for a failed delivery, a defective file, a duplicate purchase, or a pack materially different from its description. See Section 6 of our Terms of Use.

Questions about the East Greenwich, RI pack?

Not ready to buy, or need a different jurisdiction? Tell us and we’ll reply directly.

By submitting, you agree to our Terms of Use and Privacy Policy.

Sources

Roofing questions: East Greenwich, RI

Is ice & water shield required in East Greenwich, RI?

Yes. Required statewide. Rhode Island replaces the International Residential Code's Table R301.2(1) with its own table for the whole state, and that table reads "Ice Shield Underlayment Required" "Yes" (510-RICR-00-00-2, R301.2). Section R905.1.2, adopted unchanged, then requires an ice barrier "for asphalt shingles, metal roof shingles, mineral-surfaced roll roofing, slate and slate-type shingles, wood shingles and wood shakes," consisting of "not fewer than two layers of underlayment cemented together, or a self-adhering polymer-modified bitumen sheet," extending "from the lowest edges of all roof surfaces to a point not less than 24 inches (610 mm) inside the exterior wall line of the building," and on roofs of 8:12 slope or steeper also "not less than 36 inches (914 mm) measured along the roof slope from the eave edge of the building." The rule does not apply to "Detached accessory structures not containing conditioned floor area." On a tear-off, an ice barrier membrane adhered to the deck may stay and be covered with an additional layer (R908.3, Exception). Everything above is Rhode Island state law, the same in every city and town. In East Greenwich the Building Department, within the Department of Public Works, guides applicants through permitting and inspection, and takes permit applications through the town's e-permitting portal, according to the town's own page.

Is drip edge required in East Greenwich, RI?

Yes. Required on shingle roofs. Rhode Island adopts the 2021 International Residential Code with "Chapter 9 is adopted with no changes" (510-RICR-00-00-2), so Section R905.2.8.5 applies as published: "A drip edge shall be provided at eaves and rake edges of shingle roofs." Segments overlap by at least 2 inches, the drip edge extends at least 1/4 inch below the roof sheathing and at least 2 inches back onto the deck, it is fastened at no more than 12 inches on center, and "Underlayment shall be installed over the drip edge along eaves and under the drip edge along rake edges." A reroof is held to the same chapter: "Materials and methods of application used for recovering or replacing an existing roof covering shall comply with the requirements of Chapter 9" (R908.1). Everything above is Rhode Island state law, the same in every city and town. In East Greenwich the Building Department, within the Department of Public Works, guides applicants through permitting and inspection, and takes permit applications through the town's e-permitting portal, according to the town's own page.

Can you roof over an existing roof in East Greenwich, RI?

Two layers at most. Rhode Island adopts the 2021 International Residential Code with "Chapter 9 is adopted with no changes" (510-RICR-00-00-2), so its reroofing section, R908, applies as published. Section R908.3.1.1 says "A roof recover shall not be permitted where any of the following conditions occur," and the third condition is "Where the existing roof has two or more applications of any type of roof covering." So one existing layer may be covered once, and a roof that already has two layers is torn off to the deck. The same section also bars a recover "Where the existing roof or roof covering is water soaked or has deteriorated to the point that the existing roof or roof covering is not adequate as a base for additional roofing" and "Where the existing roof covering is slate, clay, cement or asbestos-cement tile." A tear-off means "the removal of existing layers of roof coverings down to the roof deck" (R908.3). Cities and towns may not enact building codes of their own (R.I. Gen. Laws 23-27.3-100.1.7). Everything above is Rhode Island state law, the same in every city and town. In East Greenwich the Building Department, within the Department of Public Works, guides applicants through permitting and inspection, and takes permit applications through the town's e-permitting portal, according to the town's own page.

Do roofing contractors need a license or registration in East Greenwich, RI?

Yes.

What building code does East Greenwich, RI use?

The Rhode Island One and Two Family Dwelling Code (RISBC-2, 510-RICR-00-00-2), which "adopts and incorporates as the Rhode Island One & Two-Family Dwelling Code the provisions of the International Residential Code (IRC), 2021 edition," effective December 1, 2025, and which applies "to the construction, alteration, enlargement, replacement, repair, equipment, use and occupancy and location of detached one-and two-family dwellings and multiple single-family dwellings (townhouses) not more than three stories in height" (R101.2). The State's adoption says "Chapter 8 is adopted with no changes" and "Chapter 9 is adopted with no changes," so the roof framing, sheathing and roof assembly rules apply as the International Code Council publishes them. The same code applies in every city and town: the State Building Code applies "to all buildings and structures" (R.I. Gen. Laws 23-27.3-101.0), and "the local cities and towns shall be prohibited from enacting any local building codes and ordinances in the future" (23-27.3-100.1.7). A 2026 act requires a newer edition: "The 2024 IRC, including any amendments thereto adopted by the building code standards committee ("BCSC"), shall take effect" for one- to three-family dwellings "not later than January 1, 2027" (P.L. 2026, ch. 377, adding subsection (f) to 23-27.3-100.1.5). Everything above is Rhode Island state law, the same in every city and town. In East Greenwich the Building Department, within the Department of Public Works, guides applicants through permitting and inspection, and takes permit applications through the town's e-permitting portal, according to the town's own page.